"Fix" your 2012 Nexus 7 slowness on Android 5.0 Lollipop and above.

If you've got a 2012 Nexus 7, then updating it to Android 5.0 Lollipop and over is likely to be the worst mistake you can make in regards to the software on this tablet. If you did not upgrade it yet to Lollipop, I would recommend NOT doing it (yes, I know, update notifications can be annoying). If you updated it, then just keep reading. I will explain to you what you can do in order to relieve yourself from the stress that any 5.0 and above firmware is creating while using the tablet.


There is one single thing that can be done in order to fix the incredibly poor performance of the tablet: to downgrade it to Android 4.4 KitKat or below. Trust me, I have tried almost 10 different ROMs which run from 5.0 all the way to 5.1.1, and I am still trying to understand what is going on through the head of whoever is responsible at Google for providing these updates on the tablet.

Luckily, since it is an Android tablet, downgrading is extremely simple.

• if you've got a tablet with an unlocked bootloader and a custom recovery, I would recommend following getting this link and getting the provided ROM (it is pre-rooted). I've got the Odexed 1.6 version and it works flawlessly. Since you are downloading this version, I assume you already know how to flash that (gapps are included and do not need to be flashed separately);

• otherwise, you can follow this official link for the official Factory Images (I would recommend downloading the 4.4.4 image). More detailed instructions are available here, but please make sure you are downloading a pre-Lollipop version and flashing that on the device, not the latest version which is 5.1.1!

The reason for the extremely poor performance of the 2012 Nexus 7 on Lollipop ROMs is not clear. People speculate it might be due to flash wear-out but this is highly unlikely due to the fact that KitKat is running as new once installed. It is true that it has only 1GB of RAM and the pressure for low prices might have forced Asus to put low quality (thus slow) components that provide insufficient IO speed. But that does not explain the fact that a similar device which was also sold cheaply, the Nexus 4 is absolutely flying through Lollipop (the Nexus 4 does have 2GB of RAM, but this is not an excuse for the low memory killer on all Lollipop versions not being much more aggressive in order to keep the tablet usable, this, of course, provided that RAM was the culprit). 

Thank you for reading these and please let me know if downgrading to KitKat managed to help you!

Chrome 20 might be the most unreliable browser to use on Ubuntu.

I'm a big fan of Google's products, and of course that this includes Chrome, but Google's lightweight browser is not worth being considered as the best one from all the available ones, at least on Linux. Ubuntu (because that's the OS I use most of the time) comes with Firefox for this: even though it is not as fast as Chrome, it is rocket-stable and fully usable (free of bugs). But Chrome has been having bugs since a long time ago and it has some even now. And what's worse, Chrome 20 "features" more bugs than ever.

First of all, there are huge issues with Flash. Most of the content from YouTube still uses Flash (please note that YouTube is also owned by Google), and one of the most used ways make a video start again is to refresh the page. And I have to do this because I simply can't click on anything that's Flash related, for I-don't-know-what reason. Moreover, Samsung's Chromebook computer, which runs on Chrome (there's nothing else to choose) has the same problems with Flash.

Then, there is the Blogger platform. You can write everything you want (just like I do now), but you can't put a title in the article (note: the article is going to have a title put on Firefox, just because Chrome can't do it for a reason or another). And here we are talking about two Google products. Blogger, a Google product, can't be properly used on Chrome, Google's browser. I am sorry, but this is something incredible, and Google should have taken action long time ago on this subject.

And there are other, not so serious, but still annoying bugs. On 9gag, portions of the bar from the top of the screen spread across the entire screen while scrolling. On YouTube, the same thing happens with the bar located just below the videos. And more that this, while watching something, you can't see what you type when you search for something else (on YouTube), it just displays what was searched before (it still searches, if you write something and tap enter you'll see it will return what you wanted, but it's annoying).

Of course that these aren't the only bugs, but with these I have to deal day by day. My girlfriend complains that she can't enter full screen while watching some TV series on the internet (don't know whether it's Flash or not), but there clearly are some issues Google have to take care about.

I can't simply give up using Chrome because, as I've told, I'm a big fan of Google's products, and I have more computers, so I need sync across all of them (bookmarks and stuff). Owning a Galaxy Nexus is also a strong reason for using Google's products. And I don't even want to give up using them, because they make the life a lot easier (Gmail, Picasa, Drive, Contacts, Calendar, Maps etc), I use them a lot and they help me everyday, but the idea is that some of the bugs really have to be fixed sooner or later.

I don't know if they are present only on Linux, because I rarely use Windows, and when I do it, I don't usually have a lot of time to spend on YouTube, 9gag or such websites. 

If you're on Android, just don't use NetTraffic Monitor (from PopSoft) to monitor your traffic. It causes only issues.

NetTraffic Monitor is an app from Android Market which claims to be capable of monitoring your data traffic. It seemed quite weird to me even from the first run, because it requested me super user access (I'm running on a rooted device), even though its only work was to view and count my traffic, and nothing more.

After I installed it, I observed that the internet over 3G/2G networks was no longer working (the device was sending data, but it wasn't able to receive back anything). Actually, I didn't realize that the problems started after I installed NetTraffic Monitor, it took me about 2 days to realize that (during that time, I spoke with my carrier, thinking that they had problems with the network).

The app indicated only about 30 kb during that two days on mobile data networks, and absolutely no traffic on WiFi, even though I probably had about 50 MB on it. So I decided to uninstall it because it was useless (I also realized then that the problems started after its installation), and after the uninstall, guess what? The internet started working normally, and I haven't got any problems since then.

The app is the first one if you search for "Traffic Monitor" in the Market, so just be careful what you install and what you don't.

In case you have issues with Market on your Android device, here is what you can try.

As you probably know, there are somewhere around 100 000 apps currently available in the Android Market, growing faster and coming forcefully behind Apple's App Store (which has around 200 000 apps). Is isn't currently any problem for Apple, but there's a matter of time until there will be a real challenge for Apple to keep up with the incredible grown of the Android Market.

However, the Market (the place from where apps for Android are officially installed) isn't a perfect app. Actually, it's quite buggy, maybe too buggy in some situations. Nexus One, a device on which the Market worked perfectly and which is considered "the Google Phone", got some problems since it was updated to 2.2. There weren't big problems until about a month ago, and, from then, my phone fails most of the times to install some updates (when more updates are available in the same time).

This is a common problem on many Android devices, and here is what you can try in order to get Android Market working properly. First, disconnect your device from wifi. Then go into Settings | Applications | Manage Applications | All (if these steps doesn't correspond to your device, just find in the settings the list with all apps).

From there, scroll down to "Market", tap on it, and then tap "Clear data", "Clear cache", and "Force stop". This will practically clear everything Market had saved about your apps. Then, connect again to wifi, and start Market. You'll be asked to Accept the "Terms of Use", and then it will list all your installed apps and the available updates on "Downloads" (just like it was before).

Now, just don't force it to update everything. Update every app from the update button (inside the app page), and make sure you don't update two or more apps in the same time. Otherwise, it will continue failing to update some of the apps.

Keep in mind that this is just a temporary solution, and doesn't work at all times. Additionally, make sure you have enough free internal storage memory on your device, as this could be the problem in some situations.

Apple just released iTunes 10.0.1, fixes lots of bugs.

Apple has just released a new version of iTunes, 10.0.1, which brings improvements to Ping (more exactly, it adds a new sidebar for it), and fixes lots of bugs. Here's the changelog of this update:

iTunes 10.0.1 makes it easier to share your favorite music with your friends on Ping. You can now Like or Post about music right from your iTunes library. You can also easily see the recent activity of a selected artist in your library, or of all artists and friends you follow on Ping using the new Ping Sidebar.

This release also provides a number of important bug fixes, including:

• Addresses an issue where the picture quality of a video changes depending on whether the on-screen controls are visible. 

• Resolves an issue where iTunes may unexpectedly quit while interacting with album artwork viewed in a separate window. 

• Fixes a problem that affects the performance of some third-party visualizers. 

• Addresses an issue where the iTunes Library and playlists appear empty. 

• Resolves an issue that created an incompatibility with some third-party shared libraries.

iTunes 10 comes with many new features and improvements, including:

• Introducing Ping. Use Ping to follow your favorite artists and friends or connect with the world’s most passionate music fans. Discover the music everyone is talking about, listening to, and downloading. 

• Rent HD TV episodes for just 99¢ each. Watch them on your Mac or PC, on-the-go with iPhone or iPod touch, or in your living room with the all new Apple TV. 

• Play your favorites on the all new iPod Touch, iPod nano, iPod shuffle, and Apple TV. 

• Play music wirelessly with AirPlay on AirPlay-enabled speakers, home theater receivers, and iPod accessories. 

• Explore many look-and-feel improvements throughout iTunes. 

• Enjoy performance improvements which make iTunes faster and more responsive. 

• Additional voice support with VoiceOver Kit for iPod.

It is not clear if this causes any problems with jailbroken devices, so if you have jailbreak on you iDevice, just stay away from it for now.

You can either get this new version via the Apple Software Update utility (on Mac), or you can manually download it for here (Windows & Mac users).

Samsung S2 are quite good external HDDs. Unless you're going to use them with Multimedia Players (Popcorn Hour/WD HD TV).

Samsung S2 external HDDs are quite attractive products. Mostly because of the variety of capacities, and because of the available colors. So, they look good, they are perfect for backups, and they work well (I get somewhere around 25-30 MBs reading/writing rates on my computers). But if you're planning to use them with multimedia players, such as Popcorn Hour or Western Digital HD TV Media Player, they are going to give you an enormous headache.

I also got one, a blue one, with 640 GB, and I have some issues with it. As long as it is on FAT32 file system or HFS+ (Apple native), it works like a charm, both on my Popcorn Hour and on my WD HD TV. But when I'm converting it to NTFS, it is completely unreadable by my both multimedia players.

WD HD TV used to say that it didn't recognize it, but after I was told that an unofficial firmware might make it work with my HDD, now it doesn't react at all when I'm connecting my HDD to it. On Popcorn Hour, it simply says that "USB failed". I tried connecting it through an external USB hub (which was externally powered), in order to exclude the possibility of failing because of not getting enough power, but the S2, formatted on NTFS, won't work at all.

I found on some forums users complaining of this (reproducing exactly the same situation, the S2 work on these multimedia players as long as it isn't formatted as NTFS), but there's no fix for this (only some suggestions that were tried by everybody having these issues, suggestions that don't help).

If you're stuck here, you can format the external HDD as HFS+ (FAT isn't an option, as it has  limitations), and then install MacDrive on your Windows computer (unfortunately, you have to buy it), which will give you the possibility of both reading and writing to HFS+ partitions from Windows. I don't know if MacDrive can format the HDD as HFS+, because I did it from my MacBook.

Anyway, the idea is that if you want to buy an external HDD and you're planning to use it with a multimedia player, you should avoid Samsung's S2 external HDD.

Solving AccuWeather's app force close problem (Android).

If you're an Android user, you probably know that after the latest update, AccuWeather app stopped working and everybody complains about this (any device, any Android version). It simply force closes after the launch. It seems that AccuWeather is never going to update that app, so I found a way of getting AccuWeather data on your device, under the same interface.

There are more AccuWeather apps in the Market, if you search for them. However, I've found one which really works, so if you search for "ACCU WEATHER Quick" (yes, ACCU WEATHER with capital letters), you'll get an AccuWeather app which really works. It seems to be released by Accuweather.com (nobody knows exactly), and it has a few bugs, but at least it works. Some users reported problems with the widget, problems that I don't confirm. There were also reported some problems with the accuracy of displayed information, but as I've just downloaded it, I think that the information is quite accurate.

So, go to the Market and download "ACCU WEATHER Quick" app to see if that one works for you.

Twitter API changed (again), most third-party clients are failing to authenticate.

Twitter announced on its official blog that starting from August 31st, its API is going to be changed. All third-party clients/applications are now logging on via OAuth, a new method of authentication that doesn't require them to store your username and your password anymore (this has the purpose of increasing users' security). This new change requires some changes in all third-party clients/applications, changes that the guys from Twitter say that they have been done.

They say that most clients, such as Echofon, TweetDeck, Twitterific, Seesmic, and Twitter for Android, iOS and BlackBerry are already authenticating through OAuth, which is not true. TweetDeck, Seesmic and Twitter (all on Android), are all refusing to sign in. I've last checked a few minutes ago, and there is no update into the Market (for any of the specified apps) to fix this problem. Bad, very bad, Twitter!

If it's necessary, I can make a video for Twitter (or for any other company providing third-party clients for Twitter), proving that the mentioned clients cannot connect at all.

Seesmic force close problem was fixed a few minutes ago via an update !!

Seesmic announced a few minutes ago on their official twitter account the availability of an update in the Market, which promises to fix the problem with the Twitter API users from all over the world had today (which was causing Seesmic to force close). However, it seems that the problem has been fixed for the previous version also (maybe Twitter changed something at their APIs in the same time?).

The new version is 1.4.3, and yes, I confirm that it fixes the problem.

Setting up WDS between Asus WL 520GU and 520GC + WPA encryption gets the whole network into a conflict.

I've decided a few days ago that in order to improve the security of my wireless network, I should change the encryption of the network from WEP (which can be decrypted in under 60 seconds, that's proved), to WPA (which can resist even a year to a decryption attack, experts say).  The reasons was that I had some doubts about the devices operating on my network, but everything is clear now (I have over 10 devices usually connected on the network).

I have two Asus routers, a WL 520GU one (with print server), and a WL 520GC one. I've written some time ago an article on how to set up WDS (or Wireless Distribution System) between them (a method of improving signal into your house for example, by setting them to operate in the same way, under the same name), which is available here (it should be applicable to almost any other models of Asus routers).

So, let's return to the problem from the title. I've changed their both encryption method to WPA, and I've let them continue working. Everything worked smooth for a few tens of minutes, than my devices were disconnected.They reconnected very fast (a few seconds), and continued working, again, for a few tens of minutes.

Then, suddenly, the entire network crashed, all devices were disconnected, and all tries to reconnect failed, as the main router (from which comes the internet connection) was refusing to give addresses to the devices requesting them. I said that it refused to give addresses, because it is practically the one doing the whole job, with the second one only repeating what it "says" to the network. As I wasn't able to receive the addresses, there was no possibility of getting into the routers in order to check the reports to see what could possibly fail like this. A restart of the routers (disconnecting their power cables) made the network start working again (this happened somewhere around 1:30 A.M. in the morning).

And they continued working until the following afternoon, when the network crashed again, creating exactly the same situation. I've searched for an update for the firmware of the routers, but there wasn't any. I've also searched to see if somebody else was having the same problem, and I found a few users reproducing quite the same situation, but the provided fixes were not helping at all.

I changed the encryption back to WEP in that afternoon, and everything has been working perfectly since then (very stable). I can't imagine what could be the problem that caused that crashes, probably that there's an incompatibility between these routers when they're operating in WDS while encrypted with WPA.

So, I repeat. If your Asus WDS crashes while secured with WPA, try changing that with WEP. Hope this helps you.

Ubuntu 10.04.1 released, if you used Update Manager regularly, you already got it.

Ubuntu 10.04.1 has been released, WebUpd8 announced yesterday. Like usually, this version puts together all the updates that Ubuntu 10.04 had until now. So, if you used the update manager regularly, you already have it. It has been released just for those two want to make a fresh install of Ubuntu 10.04 (because this version has all the updates until now and they don't have to wait to download and install them).

This is what is called a maintenance update, and it's available for both desktop and server versions, and for both i386 and amd64 architectures.

It's available for download at the known, official download page, here.

AccuWeather Android app gets an update which breaks it.

AccuWeather.com is probably one of the most known weather websites in the world (together with weather.com), and it has, of course, a dedicated app in the Android Market. It has been recently updated (I don't know exactly when because I just came from Greece and I couldn't see there any updates because of the weak connection I had), so I updated it today.

It has a much cooler interface than before, but, unfortunately, it crashes every time I try to open it. It can be used for about one second, then, it stops working and has to be force closed. I'm running Android 2.2 on a Nexus One, but it seems that this doesn't matter, as everybody reports the same problem after update. I've already reported the problem, and the guys from AccuWeather have to move fast, because even if the app currently has 3 stars and a half, I'm sure that its rating is going to fall soon.

Ubuntu 10.10 Alpha 2 getting out of control.

A few days ago I presented you Ubuntu 10.10 Alpha 2 (here), telling you that it has some bugs at sound (it doesn't work at all with some sound cards) and at booting procedure (or more exactly, it fails the installation procedures and is forced to boot in live CD). However, there is another critical bug that I experienced a few minutes ago.

Here are some details: Pidgin + Chrome were running (nothing else) while I was notified that Gwibber crashed (it was not running, I didn't open it). Everything is...normal until now, I periodically receive notifications telling me that Gwibber crashes (even without running it). But what happened after was....let's say, normal for a pre-release version of Ubuntu. The main problem is that you it makes it difficult to save what you were working on at that time. This is what I'm talking about.

When Gwibber crashed, "Report a problem" has opened, in order to let me send details to developers, to help them fixing the problem. And it seems that, I don't know why, "Report a problem" crashed after that, too. And again. And over and over again. I think that every second, two windows of that type were appearing. That's not much, I know, but for my desktop, which doesn't have video hardware acceleration (lack of drivers), they are a real problem, as it is hard to save anything.

So, here's a new bug that developers need to fix for the final release of Ubuntu 10.10.

Chrome dev version fixes most of the problems.

You probably read my article about that stupid bug from Chrome, which keeps aleatory some windows unmaximized even if they are maximized, right? (more here). And you probably seen (or not) Andrew's comment from WebUpd8, who recommended me today to try the latest unstable version of Chrome, which is an Alpha one.

It seems that this version fixes this the bug that I had. It adds some updates to the interface. That loading signs from the tabs have changed colors, and the interface at tabs and at the buttons under them seems to be a little redesigned. Loading speed of webpages has been improved. However, remember that this is an Alpha version and it can crash when you need it more, so this version is more recommended for testing purposes.

If you want to install it and you already had a version of Chrome installed, I recommend you doing it via Synaptic Package Manager, in order to avoid any conflicts that might occur from installing the latest version over the previous one. If you didn't have Chrome yet, go on SoftPedia here and download the latest version corresponding to your OS. Please note that the latest version on Linux is 6.0.453.1 dev, so try to search the same version for your platform.

Apple promises to fix iPhone 4 signal problems via software update, experts say it's impossible.

Apple published today a letter regarding the iPhone 4 and its signal problems. Officially, it seems that the device really has some problems with the signal, and not the users were actually causing that problems (letter is available here). Apple declared that they have a failing algorithm which calculates the power of the signal, and explained the problem into the letter. They also promised that they are going to fix that problem via an update (in a few weeks), thanking everybody for their patience.

The wireless specialists don't agree with Apple. However, they say that the thing with the bad algorithm can be true, an update can possibly improve the accuracy of the displayed bars (they aren't currently displaying the real signal). But, there still is a problem. The phone loses completely the signal while in the hand, and this isn't a problem caused by a badly configured software. The experts say that this is a problem with the design of the device, when you cover with your fingers or your hand the region which causes the current problems, it will lose the signal in any situation. It doesn't matter what software it is or how it is configured, this is simply a problem with the design of antenna. 

I'm curious to see what happens when Apple will launch the next update, and which will be the people's reaction if the wireless reception problems will not be fixed. 


Full article on Gizmodo here. 

Fixing "connection refused" problem in Pidgin (Ubuntu).

"Connection refused" error is a problem which is known by many Linux users. It is usually occurred (sometimes) on most IM clients, especially when trying to connect to Yahoo!. This is a very annoying problem, and almost nobody knows exactly how to fix it (and if they fixed it, what they really did). Certain is that this usually occurs when the guys from Yahoo! are changing the way users are authenticating on their servers. So their servers are probably misconfigured (for Linux users), and they are simply refusing all clients who are coming from other clients, different than their own client (application).

There are some ways of fixing this on the internet. It has been reported that if you continue trying to connect, you could be in a final connected or redirected to a server which allows authentication in the old way. However, theoretically spoken, this solution is only temporary. If you disconnect, you'll probably have again problems connecting. Other users reported that changing the server on which the application is logging on may resolve the problem. I've tried changing it between scsa.msg.yahoo.com, cn.scs.msg.yahoo.com, scs.msg.yahoo.com and other addresses like these. I tried to change the address even with server's IP address directly (thinking that it could be an address resolving problem), everything with no luck.

But I continued trying, and after tens of forums and blogs, I found on brainstorms.in a user who reported that changing the server to scsd.msg.yahoo.com works. And it really works. So, if you have this problem, click on Accounts -> (on your account) Edit Accounts -> Advanced, and on the first row (Pager server), put "scsd.msg.yahoo.com".

Please leave a comment to know if this fixed your problem or not.

Ubuntu 10.04 + Nvidia FX proprietary drivers? Maybe not!

I never was a fan of Nvidia's graphic cards. I don't have a reason for this, but I simply prefer ATI's products. And after what Nvidia proprietary driver did when I activated it in Ubuntu 10.04, I surely won't be a fan of them ever. So here are the details. An AMD platform (32-bit), with a Nvidia FX 5600 graphic card and a fresh-installed Ubuntu 10.04.

Nvidia usually makes its own drivers for Linux distributions. These kinds of drivers are known as "proprietary drivers", which means that their code is made and developed by Nvidia developers. In Ubuntu, in case that something goes wrong (including a driver), developers (from anywhere in the world) start working (on open source code) immediately on a fix so that it is available as soon as possible in the Update Manager. But with Nvidia, the situation is different. Because it's a proprietary driver, Ubuntu's developers doesn't have access to the code (because it isn't a public or open source code), so they can't improve or fix it. Any user using a Nvidia graphic card under Ubuntu has to wait for Nvidia's developers in case that it appears a problem with the driver.

So here's my problem. After I activated Nvidia's driver (version 173), it asked for a reboot. Until then, everything worked fine. But after reboot...it happened...I don't know what. I can't even explain. Under the VGA port, the image was highly affected. I could hardly read something on the screen (the colors and the image were totally misplaced). The monitor (Samsung T220) was continuously warning me that the image is displayed in "not optimum mode", and even after I got into driver's settings and changed them from auto to 1680 x 1050 with 60 Hz, the situation remained the same. The image on the monitor was starting to color white at every 10 seconds, and I was afraid that this can burn the pixels or even broke the entire monitor.

On DVI, the situation was completely different. The image looked pretty OK, however, the monitor was still warning me that it is in "not optimum mode" and it was restarting at every 1-3 seconds. This happens both with driver version 173 which is recommended, and with version 96 to which I have access.

In now stuck on a desktop without any accelerated video driver, but at least, this works (even if it is quite slow). The only thing I can do is to hope and wait for Nvidia to update their stupid driver for Ubuntu 10.04. I don't know why, but I think that Nvidia won't change something here...I hope I'm wrong. I know that there are some open-source drivers for Nvidia called "Nouveau" but I observed that they are only for GeForce6 and above (mine is GeForce 5).

So, if you installed one of these drivers with problems, try to enter into "hardware drivers" to remove it, and then reboot. In this way, you will be able to use your computer.

If you know how to fix this, please let me know via a comment.

Ubuntu 10.04 has 2 important bugs since 13th of June - with all updates installed -.

The first problem is with the sound. What you should do is to avoid putting the sound on mute, because you won't be able to start it again. This is what I did yesterday. And now I realized that I don't have sound anymore. It doesn't matter what settings I give to the system in sound preferences, because on the bar it just displays the speaker followed by three lines (3x "-"). This means that the sound is muted, even if in all my settings the sound is on. Of course that "waking up" the sound would be theoretically possible with third-party programs from the Software Center, but I'll let my system like it is, just to see how much it takes for developers to fix this.

The other problems is related to the...shutdown. Here it is a critical bug, which brings you to the login screen, when you select shutdown. I don't know why, but now the shutdown button has the same functionality as the log out one. Practically, there is now way to shut down your system from the OS. In case that you are here, what you can do in order to shutdown your system is to push and keep the power button on your PC/Laptop for 5 seconds (this cuts the power of your computer), or to unplug it from the power source (if you are on a laptop, use the first option). Both are improper ways of shutting down the system, but there is no alternative.

Note: My Ubuntu is up-to-date, at 9:15 GMT time, Monday, 14th of May, and the problems are not fixed. If an update appears in the update manager which fixes these problems, I'll update this article.

Is Yahoo! Messenger for Mac going to be a beta version forever?

I bought my Mac almost a year ago (10 months), and when I received it I hoped that it would support Yahoo! Messenger by default. I knew that Mac OS X is a very stable and a very complex OS. And mainly, so it was. Except that iChat, the default chatting application from Mac OS X, doesn't support anything else than MobileMe, Mac.com, AIM, Jabber and Google talk accounts. So here started the problem...Apple didn't implement a client supporting Yahoo!, so it was clear that I had to use Yahoo!'s own application.

I was surprised that at least there was a program developed by Yahoo!, for Mac. It was a beta, and it was the only option that I found for Mac. After installation, I noticed several problems, such as: unexpected crashes (prior to this the application becomes unresponsive), a bug which doesn't allow you to click on a contact (you have to move the pointer in order to do that), and the most...idiot problem, that one which displays you as "available" even if you logged in as "invisible". OK, you are "invisible" for all others, but you see yourself as "available". And this happens always.

What I consider that sucks is that you see only the small avatars of your contacts in the list, and if you move the mouse over a contact you will see only its name and status, without the picture. If you want to view the picture in "large" size, you have to open a window chat for that person. On Windows version of Yahoo!, you can view large pictures even on the list with all contacts (there's an option for that).

Those aren't critical problems, but they are very annoying because they seem that they will never be fixed. Yahoo! didn't launched any new version since I first installed it (it's still 3.0 beta (191946) ) and I don't think that Apple is going to move a finger to do something. But I still hope that Yahoo! didn't abandoned at all developing their application for Mac...

Ubuntu One - note facilities only- is down (15:00 GMT Time, Saturday, 15 May).

Today I needed to look over a note I had made a few weeks ago, but after logging in, when I wanted to view my notes, I had a surprise. I got a screen like this.

As you can see in the picture, there is a problem with the notes. It says that "Something has gone wrong", with the error 500. This is really strange, because the files are available, only the notes are failing. And this was a moment when I really needed a note.

I hope that this problem won't take much time, and that my notes will be back again.

Update: 10:30 A.M, 16 May, notes are available again. All notes are in their place. No one has been lost.